KERATIN 250ML

TRADITIONAL APPLICATION METHOD:

Step 1: WASH YOUR HAIR 3 TIMES with warm water and the deep cleansing ritual, STEP 1 (included); leave on for 5 minutes and rinse thoroughly with plenty of water. It is important to remove any traces of treatment, styling cream, grease, dust, and dirt from the hair fiber to allow for homogeneous absorption of the keratin throughout the strand.

Step 2: DRY IT 100% with a cold-temperature blow dryer and gently detangle from the ends upwards.

Step 3: APPLY THE ULTRA PROTECTIVE BIOSERUM to the scalp. Take the sachet, spread the product on your fingertips and gently massage your entire scalp for 30 seconds for better absorption. Let the product act for 5 minutes and continue with step 4, without rinsing.

Step 4: APPLY THE KERATIN in an open and well-ventilated area, wearing a face mask, gloves, and protecting your clothes. Divide your hair into sections, use clips to separate it and ensure an even distribution of the keratin. Start with the front section: using a brush, apply the keratin in thin strands, making sure to impregnate well up to the ends without touching the scalp (maintaining a distance of 5 mm from the root). As you apply the keratin, use a fine-toothed comb to remove excess. Repeat the process on each section of hair.

Step 5: LET THE KERATIN REST in the open air as follows:
- AFRO, very curly, thick, virgin, henna-treated hair: 90 to 120 minutes.
- Hair with slight frizz or somewhat wavy: 45 to 60 minutes.

Step 6: WITHOUT RINSING, DRY YOUR HAIR 100% with a medium-temperature blow dryer, in an orderly manner and without ruffling it, without brushing or combing. Never flat iron your hair wet; not drying it well can cause your hair to burn when flat ironing due to the moisture turning into steam, affecting your hair health.

Step 7: FLAT IRONING PROCESS: Before starting, clean your titanium flat iron, adjust the temperature between 210 °C (410 °F) and 230 °C (446 °F) and observe how your hair reacts: if it shrinks, smells burnt, or feels rough, STOP! This indicates that the flat iron temperature may cause damage to your hair fiber. Once you have determined the appropriate temperature for you, divide your hair into sections and take thin strands. The number of passes and the temperature will depend on the condition of your hair. Pass the flat iron in one direction 7 to 10 times until a smooth finish is achieved. In finer areas or at the ends, reduce the temperature and apply less pressure.

Step 8: REST FOR 20 MINUTES AND THEN WASH YOUR HAIR PERFECTLY ON THE SAME DAY OF APPLICATION with plenty of warm water and salt-free and sulfate-free shampoo. WARNING: DO NOT USE STEP 1 OR THE DETOX SHAMPOO! We recommend the products from our post-care line designed for each type of scalp. Finish with a mask from mid-lengths to ends and rinse. Dry with a medium-temperature blow dryer, 15 cm away and vertically, without ruffling it. No brushing is necessary.

FLEXIBLE APPLICATION METHOD:

Step 1: WASH YOUR HAIR 3 TIMES with warm water and the deep cleansing ritual, STEP 1 (included); leave on for 5 minutes and rinse thoroughly with plenty of water. It is important to remove any traces of treatment, styling cream, grease, dust, and dirt from the hair fiber to allow for homogeneous absorption of the keratin throughout the strand.

Step 2: DRY IT 100% with a cold-temperature blow dryer and gently detangle from the ends upwards.

Step 3: APPLY THE ULTRA PROTECTIVE BIOSERUM to the scalp. Take the sachet, spread the product on your fingertips and gently massage your entire scalp for 30 seconds for better absorption. Let the product act for 5 minutes and continue with step 4, without rinsing.

Step 4: APPLY THE KERATIN in an open and well-ventilated area, wearing a face mask, gloves, and protecting your clothes. Divide your hair into sections, use clips to separate it and ensure an even distribution of the keratin. Start with the front section: using a brush, apply the keratin in thin strands, making sure to impregnate well up to the ends without touching the scalp (maintaining a distance of 5 mm from the root). As you apply the keratin, use a fine-toothed comb to remove excess. Repeat the process on each section of hair.

Step 5: LET THE KERATIN REST in the open air as follows:
- Hair with slight frizz and somewhat wavy: 45 to 60 minutes.
- Curly, thick, gray hair: 90 to 120 minutes.

Step 6: RINSE UP TO 90% WITH WATER ONLY and then dry your hair 100% with a medium-temperature blow dryer, in an orderly manner and without ruffling it. Not drying it well can cause your hair to burn when flat ironing due to the moisture turning into steam, affecting your hair health. Gently detangle from the ends upwards.

Step 7: FLAT IRONING PROCESS: Before starting, clean your titanium flat iron, adjust the temperature between 210 °C (410 °F) and 230 °C (446 °F) and observe how your hair reacts: if it shrinks, smells burnt, or feels rough, STOP! This indicates that the flat iron temperature may cause damage to your hair fiber. Once you have determined the appropriate temperature for you, divide your hair into sections and take thin strands. The number of passes and the temperature will depend on the condition of your hair. Pass the flat iron in one direction 7 to 10 times until a smooth finish is achieved. In finer areas or at the ends, reduce the temperature and apply less pressure.

Step 8: REST FOR 20 MINUTES AND THEN WASH YOUR HAIR PERFECTLY ON THE SAME DAY OF APPLICATION with plenty of warm water and salt-free and sulfate-free shampoo. WARNING: DO NOT USE STEP 1 OR THE DETOX SHAMPOO! We recommend the products from our post-care line designed for each type of scalp. Finish with a mask from mid-lengths to ends and rinse. Dry with a medium-temperature blow dryer, 15 cm away and vertically, without ruffling it. No brushing is necessary.